Filter By:
- BMX (3)
- Bottom Brackets (22)
- Brakes/Levers/Pads (35)
- Cables (8)
- Cassettes/Freewheels (22)
- Chainrings (21)
- Chains (34)
- Cranksets (14)
- Show More Categories
- Derailleurs (23)
- Handlebar Grips/Tape (22)
- Handlebars (8)
- Headsets (2)
- Pedals (26)
- Saddles (29)
- Seatposts (6)
- Shift/Brake Combinations (6)
- Shifters (13)
- Stems (9)
- Other (74)
- Show Fewer Categories
- Show More Brands
- Show Fewer Brands
- Show More Sizes
- Show Fewer Sizes
- Show More Model Years
- Show Fewer Model Years
Parts

$25.00
The split-cleat system makes cleat swapping a snap – no need to worry about losing your cleat’s position.
- Cleat Bolt Pattern: 3-Bolt
- Cleat Compatibility: Pedal iSSi , Look KeO
- Cleat bolts and washers included
- 4mm hex wrench required to install

$39.95 - $44.99
- 7075-T6 aluminum construction with 4mm width optimized for all chainguide systems to prevent chain jamming
- 0.5mm step on both sides of teeth profile to retain chain
- Deep recess chainring nut interface for better clearance
- BCD: 104mm
- Speed: 1 x 8/9/10

$21.99
absoluteBLACK Chainring Bolts are used to mount chainrings to the crank arms. Bolts are crafted from 7075 T6 aluminum and hard anodized for durability.
- Bolts use a Torx T30 interface for greater reliability
- Short bolts are used for the following chainrings: 104 BCD oval 34/36t, 104 BCD round 32/34/36/38t, and bashrings
- Set of 5

$110.00 - $129.99
The Service Course SL-80 provides comfortable and efficient positions on the bar tops, brake hoods, or down in the drops. The bar allows a neutral wrist position on the drops and a flat brake-hood transition. This minimizes the need for up-rotated bars. Drops are angled outward by 4 degrees, reducing wrist strain. Named after its 80mm reach to bring the hoods and control levers back where you want them. The ergonomic 125mm drop places the angled drop position where you can easily reach it while maintaining a neutral wrist angle. The SL-80's rounded bar top is clip-on compatible. Forged from lightweight 7075 aluminum.
- Distinctive Zipp cosmetics
- 7050 Aluminum
- 80mm reach/125mm drop designed to fit a large number of riders
- Clip-on compatible
- Lifetime warranty

$199.99
The X-Fusion Manic post uses internal cable routing and was designed around a low-profile seat cradle and seal collar to fit a broad range of frames. The mechanism is air-sprung and hydraulically locked. The remote can be run on the left or right, above or below the handlebar, but is optimized as a left shifter replacement for 1x drivetrains.
- Cable activated, hydraulic action, infinitely adjustable travel
- Double key-way design prevents lateral twisting
- Double bolt clamp with a wide range of seat angle adjustment. Fits both standard and 7 x 9 mm Carbon Rails
- Sealed cartridge internals for quick replacement
- Low profile head-seal and saddle clamp increase useable travel

$76.95
Wolf Tooth's SDM® chainrings replace your existing spider and chainring with one clean looking, light weight, and stiff piece of machined billet. These come in 3 different offsets: standard GXP, Boost and BB30. Compatibility: - These direct mount chainrings will replace your existing chainring and spider, which is attached via 3 bolts on the back side of the spider near the spindle. You will use these same 3 bolts to attach the Wolf Tooth SDM® chainring. - There are 3 offsets: Standard: 47mm chainline, 6mm offset for cyclocross and road cranks Standard: 49mm chainline, 6mm offset for GXP and long spindle BB30 Boost: 52mm chainline, 3mm offset BB30: 49mm chainline, 0mm offset for BB30 short spindle cranks - Fat Bikes: If you are planning to use this on an X9 or XX1 fat bike crankset with a 190/197 rear hub spacing use the 0 offset ring. If your fat bike has a 170/177 rear hub spacing, use the Standard 6mm offset

$59.95 - $89.99
- Standard 4-bolt ring with Drop-Stop tooth design to prevent unwanted chain drop
- Recommended for use with 10 or 11sp chain (10sp chain works on 9sp drivetrain)
- Designed and manufactured in the USA from 7075-T6 aluminum alloy
- 36g (30t)

$69.95
The Wolf Tooth 76 BCD chainrings fit any SRAM 76 BCD spider or Specialized Stout crankset.
- Features Wolf Tooth's Drop-Stop tooth design for maximum chain retention
- Drop-Stop chainrings are designed for use with 1x9, 1x10, 1x11 and 1x12 drivetrains
- Compatible with all 10-, 11-, and 12-speed chains, with the exception of Shimano 12-speed chains
- Shimano 12-speed chains require the use of Wolf Tooth's Shimano 12-speed specific chainrings
- If using a 9-speed drivetrain, use a 10-speed chain, which will provide a tighter fit for better chain retention
- Made from 7075-T6 aluminum for long life

$76.95 - $81.95
The direct mount chainrings for SRAM cranksets replace your existing spider and chainring with one clean-looking, lightweight, and stiff piece of machined billet.
More power? Check. Better traction? Definitely. Less shifting? Yup. Funky uneven pedal stroke? Not with Wolf Tooth PowerTrac Elliptical (PTE) chainrings. Our proprietary design means a slightly less ovalized ring (10%) with less aggressive timing (112 degree) than competitors versions; any change to your pedal stroke is unnoticeable for most riders, but they still provide the POWER and TRACTION benefits inherent to oval chainrings.
Wolf Tooth patented Drop-Stop wide/narrow tooth profile for the ultimate chain retention and mud-shedding ability.
Compatibility
- These direct mount chainrings will replace your existing chainring and spider or replace the direct mount ring on SRAM cranksets including the DUB cranks. The ring is attached via 3 bolts on the back side of the spider near the spindle. Note that the SRAM 12spd Red and Force AXS use a different 8-bolt mounting interface that is not compatible with these chainrings.
Specifications:
- Mount type: Direct Mount for SRAM
- Chain Compatibility: Drop-Stop A tooth profile for all 9, 10, and 11spd chains or 12spd SRAM Eagle, KMC, Connex or Wippermann chains

$9.99
CAMO Chainring Bolt Kit are designed specifically for use with CAMO spiders and rings
- Includes 5 Torx head M5 x 8mm bolts
- ED coated steel is durable
- Bolts include a blue Nylok patch for a secure installation
- Torque bolts only to 4-5 Nm and use blue Loctite threadlock

$26.99
Goatlinks are designed to optimize the derailleur's position relative to your cassette. Offered in two versions - a 10-speed and 11-speed, each is intended to improve the shifting of your 1x drivetrain.

$69.99
Wolf Tooth ReMote Light Action has a longer lever arm than the standard ReMote and is optimal for dropper posts with a harder pull or for riders that just prefer a really light actuation feel. It reduces the force to actuate a dropper by nearly a third of the standard ReMote. Based on rider feedback and tailored to work with some posts' stiffer internal springs, the ReMote Light Action is also the choice of those with thumb injuries or reduced hand strength.
- Upfront cable fixing
- Large diameter ball bearing
- Cable-kind clamp
- Low-profile, light action
- Integrated cable adjust
- Breakaway axle pivot
- High-traction lever
- Broad compatibility
$23.00
The Whisky compression plug for carbon forks is reliable and easy to use. The simple design offers excellent support and function, works great with Whisky carbon forks, and may fit other manufacturer's forks as well.

$64.05
The Wheels Manufacturing 386 EVO Adaptor for Shimano Hollowtech II Cranks adapts Shimano cranks to 386EVO-standard frames. Simply tap the adapters into the 6806 bearing in the BB shell or cups, then install the cranks using the included spacers to adjust chainline, or to take up any side-to-side movement in the crank. - Machined engineering-grade Delrin - 48g/pr Includes - (2) - 24mm ID adapters - (8 )- .7mm spacers

$61.00
Machined engineering-grade Delrin inserts for adapting bottom brackets to a different type of crankset spindle. - Adapts PF30 and Cannondale BB30-73A bottom brackets for use with Hollowtech II cranksets - Delrin adaptors fit between bearings and crank spindle - BB Shell Width (mm): 68 mm , 73 mm - Spindle Interface Type: Hollowtech II - BB/Frame Interface: PF30

$10.00
This Wheels Manufacturing Spacer kit for BB30 Outboard bottom brackets includes 42mm ID spacers that fit between the BB30-OUT cup and the frame's bottom bracket shell. Use spacers for adjusting chainline. - 42mm ID - Black anodized aluminum Includes - (1) x 2.5mm - (2) x 1.0mm

$61.00
Wheels Manufacturing BBRIGHT BB30A and PF30A Adaptor for 24mm Spindle Cranks adapts 24mm spindle cranks (Shimano, FSA, etc.) to most BBRight frames. Compatible with 2011-2012 Cervelo models R3, R3 Team, S5, S5 Team, S5 VWD, R5ca and R5 VWD. - Also adapts Cannondale BB30a and PF30a frames to 24mm spindle cranks (Shimano, FSA, etc.). - Includes eight 0.7mm shims for fine-tuning chain line - Machined engineering-grade Delrin - 48g/pr

$48.00
All Wheels Manufacturing replacement derailleur hangers are produced in their Colorado shop to exacting tolerances. - CNC machined 6061 aluminum - Black anodized finish - Includes (1) M8 Chainring Bolt

$40.00
All Wheels Manufacturing replacement derailleur hangers are produced in their Colorado shop to exacting tolerances. - CNC machined 6061 aluminum - Black anodized finish - Includes (2) M5x8 Flat Head Screws

$29.99
Enduro 24X37 ABEC-3 Sealed Bearing. Replacement bearing for Wheels Mfg bottom brackets for 24mm (Shimano) and 22mm/24mm (SRAM GXP) spindle cranks.
ABEC-3 bearings are the most economical bearing Enduro offers but are extremely tough and durable.
Grade 10 chromium steel balls are within 10/1,000,000" round. These are twice as round as the industry standard. 52100 high carbon chromium alloy races go through a vacuum de-gassing process resulting in the purest chromium alloy steel, hardened to R-62. Keeping everything together are riveted steel retainers and sealed with LLB type seals.
- Dimensions: OD: 37mm / ID: 24mm / Width: 7mm
- ABEC-3 - Grade 10, 5/32" chromium steel balls
- Enduro Part # BB MR 2437 LLB-BLK
- Imported
- Sold in a bag of 2

$8.00
This Wheels Manufacturing Hollowtech II Crankarm Fixing Bolt For Late Model Shimano Road Cranks and LX keeps your Shimano crankset with 24mm spindle nice and snug. It is required to achieve perfect bottom bracket bearing preload.

$118.65
PF30 Threaded Angular Contact BB for Fat Bike. Fits Specialized Fatboy frames, and any other brand frames with PF30 x 100mm bottom bracket shell. Machined cups thread together for stability, increased bearing life, and simple installation and maintenance. No more creaking. Smooth operation. Fast bearing replacement. - Bearings: Enduro ABEC-3 - Color: Black - Bottom Bracket/Frame Interface: PF30 - Bottom Bracket Shell Width (mm): 100mm - Bottom Bracket Shell I.D.: 46mm - Crank Spindle Type: BB30 - Crank Spindle Diameter: 30mm - Weight: 130g

$123.99
T47 threaded BB cups for T47 frames and 24.00mm spindle diameter cranks. Cups have internal bearings and are typically used in BB shells with widths wider than 73mm. Machined aluminum cups thread together directly into a T47 BB shell. Bearings are easily serviced or replaced. Includes sleeve to fit between cups for added protection from dirt and grime, and also keeps your internal wires and hoses from rubbing on the crank spindle.
T47 BB cups are similar to standard BSA threaded cups in that the drive side cup is left-hand thread and the non-drive side cup is right-hand thread. Use a quality grease when installing in steel or aluminum BB shells, and an anti-seize compound compatible with titanium BB shells.
Bottom Bracket Includes:
- BB Cups with bearings
- 2x Silicone dust seals
- 2x 0.5mm crank spindle spacers
- 2x 1.0mm crank spindle spacers
Specifications:
- Bearings: Enduro ABEC-3
- Bottom Bracket/Frame Interface: T47
- Bottom Bracket Shell Width (mm): 68mm - 132mm
- Bottom Bracket Shell I.D.: 47x1.0mm Threaded
- Crank Spindle Diameter: 24.00mm
- Over Bearing Width: 91.5mm in 86.5mm wide shell
- Over Bearing Width Dimensions include supplied silicone dust shields
- Tool Pattern: 48.5mm x 16-notch
- Weight: 119g

$32.00
Wheels Manufacturing hangers are stiffer than almost any OEM hanger, which improves durability and shifting performance.
- OEM hangers are only produced by a handful of manufacturers, mostly in Taiwan and China. As a result, you will see many bikes with exactly the same hanger. Bicycle manufacturers may make mid year changes. Please use the hanger photos to select the proper hanger for your application.
- CNC machined 6061 aluminum
- Black anodized finish
- Made in the USA

$29.99
Wheels Manufacturing hangers are stiffer than almost any OEM hanger, which improves durability and shifting performance.
- OEM hangers are only produced by a handful of manufacturers, mostly in Taiwan and China. As a result, you will see many bikes with exactly the same hanger. Bicycle manufacturers may make mid year changes. Please use the hanger photos to select the proper hanger for your application.
- These hangers DO NOT INCLUDE attachment hardware with the exception of QBP # FS1561 (DROPOUT 399)
- CNC machined 6061 aluminum
- Made in the USA

$27.00
Wheels Manufacturing hangers are stiffer than almost any OEM hanger, which improves durability and shifting performance.
- OEM hangers are only produced by a handful of manufacturers, mostly in Taiwan and China. As a result, you will see many bikes with exactly the same hanger. Bicycle manufacturers may make mid year changes. Please use the hanger photos to select the proper hanger for your application.
- These hangers DO NOT INCLUDE attachment hardware with the exception of QBP # FS1561 (DROPOUT 399)
- CNC machined 6061 aluminum
- Made in the USA

$27.00
Wheels Manufacturing hangers are stiffer than almost any OEM hanger, which improves durability and shifting performance.
- OEM hangers are only produced by a handful of manufacturers, mostly in Taiwan and China. As a result, you will see many bikes with exactly the same hanger. Bicycle manufacturers may make mid year changes. Please use the hanger photos to select the proper hanger for your application.
- CNC machined 6061 aluminum
- Black anodized finish
- Made in the USA

$27.00
Wheels Manufacturing hangers are stiffer than almost any OEM hanger, which improves durability and shifting performance.
- OEM hangers are only produced by a handful of manufacturers, mostly in Taiwan and China. As a result, you will see many bikes with exactly the same hanger. Bicycle manufacturers may make mid year changes. Please use the hanger photos to select the proper hanger for your application.
- CNC machined 6061 aluminum
- Black anodized finish
- Made in the USA

$27.00
Wheels Manufacturing hangers are stiffer than almost any OEM hanger, which improves durability and shifting performance.
- OEM hangers are only produced by a handful of manufacturers, mostly in Taiwan and China. As a result, you will see many bikes with exactly the same hanger. Bicycle manufacturers may make mid year changes. Please use the hanger photos to select the proper hanger for your application.
- These hangers DO NOT INCLUDE attachment hardware with the exception of QBP # FS1561 (DROPOUT 399)
- CNC machined 6061 aluminum
- Made in the USA

$26.99
Wheels Manufacturing hangers are stiffer than almost any OEM hanger, which improves durability and shifting performance.
- OEM hangers are only produced by a handful of manufacturers, mostly in Taiwan and China. As a result, you will see many bikes with exactly the same hanger. Bicycle manufacturers may make mid year changes. Please use the hanger photos to select the proper hanger for your application.
- CNC machined 6061 aluminum
- Black anodized finish
- Made in the USA
Page 1 of 13
Next page